B – 11 Standard Test Method for Expansion (Pin Test) of Copper and Copper- Alloy Pipe and Tubing, copper, copper alloy, expansion, expansion test, pin. This standard is issued under the fixed designation B ; the 1 This test method is under the jurisdiction of ASTM Committee B05 on Copper. Find the most up-to-date version of ASTM B at Engineering
|Published (Last):||5 March 2016|
|PDF File Size:||4.97 Mb|
|ePub File Size:||17.67 Mb|
|Price:||Free* [*Free Regsitration Required]|
Standard Specification for Molybdenum Oxide Products.
ASTM B153 – 11(2017)
The purchaser shall have the option to wstm either a hydrostatic test in Standard designations usually consist of a letter prefix and a sequentially assigned number. B — 02 Standard Speci? It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Wear rubber gloves when conducting the test.
Views Read Edit View history. Rectangular including square tubes shall normally be supplied only in drawn general-purpose temper. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. The tension test for other sizes of tubes need not be made except when indicated by the purchaser at the time of placing the order. For b53 including square tubes see 5.
Originally published as B — 40 T. Grossman the Grossman method. Light-drawn bending temper is used only when a tube of some stiffness but yet capable of being bent is needed. Standard Specification for Pearlitic Malleable Iron. The purchaser shall have the right to perform any of the inspections or tests set forth when such inspections and tests are deemed necessary to assure that the material conforms to prescribed requirements.
Mercurous Nitrate Test Rockwell hardness values shall apply only to tubes having a wall thickness of 0.
List of ASTM International standards
This page was last edited on 30 Novemberat Preparation for Delivery S4. Tubes shall be passed through an eddy-current test unit adjusted to provide information on the suitability of the tube for the intended application. C Rockwell hardness values shall apply only to tubes having a wall thickness of 0. D Light-drawn and hard-drawn tempers are available in round-tube only.
Copper plus sum of all named elements shall be Limits for unnamed elements are to be established by agreement between manufacturer or supplier and purchaser.
When agreement on the Rockwell hardness tests cannot be reached, the tensile strength requirements of Table 2 shall be the basis for acceptance or rejection. If reexamined or retested, tubes with signals that are found to have been caused by minor mechanical damage, soil, or moisture, shall not be cause for rejection of the tubes provided the tube dimensions are still within prescribed limits and the tube is suitable for its intended application.
بانك استانداردهاي گاز
Retrieved August 29, Lot Size Pieces Per Lot Sample Size 2 to 8 9 to 90 91 to to to to to to 10 10 to 35 Entire lot 8 12 19 21 27 35 38 46 Grade B7 Studs bolts and Grade B16 Studs bolts fall in this category and are used for high temperature, high-pressure environments like petroleum industry.
Standard Specification for Asgm. Immediately after removal from the solution, the specimen shall be wiped free of excess mercury and examined for cracks. Standard Specification for Steel, Strip, Carbon 0.
Drawn temper is for general purposes and is most commonly used where there is no speci? C on tube sizes greater than 5 in.
Standard Specification for Ferromolybdenum. A number in parentheses indicates the year of last reapproval. Retrieved from ” https: Last previous edition B — Standard Specification for Ferromanganese.
Standard Specification for Steel Screw Spikes. Use equipment for the detection and removal of mercury vapor. This list may include either current or withdrawn standards.
Prefix letters correspond b513 the following subjects:. ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. If you feel that your comments have not received a fair h153 you should make your views known to the ASTM Committee on Standards, at the address shown below. Alternatively, if the manufacturer uses speed-insensitive eddy-current units that are equipped so that a fraction of the maximum unbalance signal is able to be selected, the following percent maximum unbalance signals shall be used.